Up
|
The best slicers - but not just slicers! Berkel product mix is broad... our range of sizes and capacities is substantial... the value is unbeatable. Berkel Model 909E manual gravity feed slicer features Berkels hollow ground chromium-plated, carbon steel knife and built-in, single lever, dual action sharpener and a number of safety features. The permanent, tapered guard covers the non-slicing portion of the knife, even when the sharpener and center plate is removed. Food Slicer, angled gravity feed, manual, 12-1/2" diameter s/s knife, s/s and anodized aluminum, belt-driven blade assembly, built-in dual action sharpener, 2 spd. motor, permanent knife guard and slice deflector, 1/2 hp. Anywhere in the continental U.S. > 1-speed, 1/2 HP, totally enclosed and permanently lubricated knife motor > Furnished in 115/60/1, 4.5 amp, AC, ETL listed. Also available in 1/3 HP, 220/60/1, 2.4 amp, AC, ETL listed. > Finish is stainless steel and sanitary, anodized aluminum; unit disassembles quickly without tools for easy cleaning > Low 12/5 VDC circuitry for added operator protection > Nominal 12-1/2” (318 mm) diameter; hollow ground, hardened and polished forged stainless steel knife > Carriage handles food up to 11” (280 mm) wide, by 6” (152 mm) high or 8” (203 mm) diameter > Rear-mounted, stainless steel meat pusher extends over the entire length of the product table > Precise slice adjustment to a thickness of 27/32” (21 mm) > Ergonomic style handle for ease of use > Built-in, top-mounted, two stone knife sharpener with single lever, dual-action system > Permanent, tapered knife ring guard covers non-slicing portion of knife even when the sharpener and center plate are removed > Q-P-Q nickel-plated transport slide rod with reservoir wick for reduced wear > On/Off, 3-position, moisture resistant switch with power light > Attached 6-foot, flexible, 3-wire cord and plug for grounded receptacle > No-Volt release prevents activation of the slicer in the event of a power interruption; operator must restart the slicer > All parts, service and travel coverage for one year, excluding wear items. 2 speed, 1/2 HP, totally enclosed, permanently lubricated ball bearings, thermally protected. Furnished in 115/60/1, 5.5/4.5 amp, AC, ETL listed. Also available in 1/3 HP, 230/60/1, 2.9 amp, AC, ETL listed. Low 12/5 VDC circuitry for added operator protection. All food contact areas are stainless steel including the pusher, gauge plate, product table, center plate and knife; sanitary burnished aluminum ring guard and one-piece base with non-slip feet. Slicer disassembles quickly without tools for easy cleaning. Nominal 12-1/2” (318 mm) diameter, hollow ground, hardened and polished forged stainless steel. Carriage handles food up to 11” (280 mm) wide by 6” (152 mm) high or 8” (203 mm) diameter. Precision gear system with eccentric gear to prevent backlash, provides infinite slice adjustment and consistent cuts of hard or soft foods from tissue thin to 27/32” (21 mm). Full 45 angle feed requires less mechanical pressure. Equipped with stainless steel, rear-mounted pusher that covers the entire length of the product table to hold product and minimize waste. An optional, screw-in weight is also available. Ergonomic style handle for ease of use. Built-in, top-mounted, two stone, single lever, dual-action system for a lasting, razor-sharp edge. Unit is removable and submersible for easy cleaning. Permanent, tapered guard covers non-slicing portion of knife edge even when the sharpener and center plate are removed. Deactivates the slicer when center plate is removed. Slicer will not run. Prevents removal of table until gauge plate is closed and the product table is in the full forward or home position. Once product table is removed the gauge plate is locked and cannot be opened. Prevents activation of the slicer in the event of power interruption. Operator must restart slicer. Built-in timer automatically shuts off the slicer after 15 seconds non-use. Highly reliable, moisture resistant, 3-position switch activates the knife motor; with power light. Q-P-Q Nickel Plated Transport Slide Rod with E-nickel plated rod undergoes Q-P-Q impregnation increasing the lubricity of the stainless steel reducing wear properties of the rod and bushings. Attached 6-foot, flexible, 3-wire cord and plug for grounded receptacle. All parts, service and travel coverage for one year, excluding wear items. As we continually strive to improve our products, specifications are necessarily subject to change without notice. or |